Linley Point Home Builder — Custom Homes, KDR, Duplex

Builder perspective

Building in Linley Point — what we actually look at first

Most Linley Point blocks we price share a pattern: 1900s–1950s heritage stock on 700–1,500m² lots, R2 Low Density / R3 Medium (Lane Cove village) zoning, and Lane Cove Council, the bushland-and-river lower north shore council sitting in the assessment chair. Lane Cove Council controls the consent — 12–16 weeks for a single-dwelling da once the package is documented properly and the BASIX score lines up. Knockdown rebuilds are the dominant build pattern on these 700–1,500m² lots because the existing stock is generally past the point where renovation makes economic sense against a $3.5M–$7.0M median. Pre-1990 stock that's still standing in 1900s–1950s heritage pockets of Linley Point almost certainly contains asbestos — that's not a defect, it's the era, and we price for it. Buildana holds HBL 487805C and statutory HBCF insurance on every job. We work to a stated value — amanah — meaning the scope on day one is the scope at handover. On a Linley Point project, the conversation that saves the most money is the one that happens before contract — feasibility, soil, planning controls, real cost ranges. That's a free conversation with us.

Linley Point site considerations

Two unknowns swing the budget on a Linley Point build. The first is geotechnical — M (sandstone ridges) / H–E (river fall) reactive soil drives different footing systems, and getting that wrong shows up as cracking 18 months in. We commission the geotech upfront and engineer to the report, not to a generic Sydney slab. The second is what's actually in the existing 1900s–1950s heritage structure when demo opens it up — asbestos in old fibro, redundant lead-jointed copper plumbing, structural rot at wet-area perimeters. The contract assumes the worst-case asbestos scope so there's no mid-job variation.

Linley Point build FAQs

The questions we get asked most often on a first Linley Point site walk.

What's the granny flat pathway in Linley Point?

Granny flats in Linley Point are usually built under State Environmental Planning Policy (Affordable Rental Housing) 2009 — secondary dwellings up to 60m², CDC pathway, no DA required on most compliant R2 Low Density / R3 Medium (Lane Cove village) lots. Typical rental return is $650–$900/week. The block needs minimum 450m², a primary dwelling already on it, and compliance with side/rear setbacks. Where the lot doesn't comply with SEPP, we lodge a DA with Lane Cove Council.

What soil class is typical in Linley Point 2066?

Linley Point sits in the M (sandstone ridges) / H–E (river fall) reactivity range based on AS 2870 site classifications we've worked with in the suburb. That drives slab design — generally waffle-pod or stiffened raft. We never assume the class; every Buildana build commissions a geotechnical investigation before slab engineering. The geotech report is yours to keep, regardless of which builder you use after.

What does it cost to knock down and rebuild in Linley Point?

End values in Linley Point sit in the $3.5M–$7.0M range based on recent sales. A typical knockdown rebuild — demo, asbestos clearance, geotech, slab, frame, full mid-spec finish for a 200m² single-storey — runs $3,000–$4,000/m² × 200m² + $0–$0k demo as a Rawlinsons-aligned 2026 baseline. We benchmark every line to the Rawlinsons Australian Construction Handbook, not back-of-envelope figures. Send through your block address and we'll run a proper feasibility against what's actually achievable on the lot.

Do you do extensions and renovations in Linley Point?

Yes — ground-floor additions, second-storey adds, full-house renovations, kitchens and bathrooms in Linley Point. The complication on 1900s–1950s heritage housing stock is that you can't price an extension off the plans alone — we pre-investigate the existing slab, frame, roof tie-in and wet-area waterproofing before quoting. Surprises during demolition are the most common reason renos blow their budget; we eliminate that by inspecting first.

How long does a DA take with Lane Cove Council?

12–16 weeks for a single-dwelling DA. CDC through a private certifier is the alternative where the design complies with the Codes SEPP — 15–25 working days for code-compliant rebuilds outside hcas. Council DA application fees fall in the $2,200–$3,600 base for a class 1a residential da range. Buildana lodges either pathway and runs all RFI responses through to determination.

Why does Linley Point cost different from a generic Sydney average?

Linley Point sits 28% above the Sydney metropolitan median build cost. Drivers are typically site access (narrow streets, restricted parking), tighter character controls requiring better materials and finishes, and trades pricing the suburb's expectation of finish quality.

How long does a custom home build take in Linley Point?

From contract signed to handover, a single-storey 4-bedroom custom home in Linley Point typically takes 9–11 months on a CDC pathway, or 12–14 months if the design needs a DA through Lane Cove Council. Add 4–6 weeks for double-storey. Pre-construction (design, engineering, BASIX, approval, contract) runs in parallel and adds another 8–16 weeks before site start. Buildana sequences both phases so the design effort and the approval effort don't sit waiting on each other.

Can I build a duplex in Linley Point?

Duplex feasibility in Linley Point depends on lot size and zoning. The minimum lot for dual occupancy under Lane Cove Council's DCP is 550m², and R3 Medium Density lots in the suburb can support attached duplex or townhouse configurations. We run a feasibility check on title, zone, area, frontage and slope before quoting — no point designing what won't approve.